N1410
New
4 Ch Reversible 1 kV/200 µA NIM HV Power Supply Module (USB)
Features
- 4 independent channels in 1U NIM module
- 1 kV / 200 µA output range
- Channels with individually selectable positive or negative polarity
- SHV output connectors
- Common floating return
- Low Ripple
- Under/over-voltage alert, overcurrent and max. voltage protection
- Interlock logic for board enable and Individual channel kill
- 5 nA Current monitor resolution (with x10 Imon-Zoom: 500 pA)
- Graphic color display
- Local and Remote control (USB2.0/RS485/RS232)
- Daisy-chain capabilty
- Optional DC Input Power Equalizer
- Software Tools for easy channel management
Overview
The CAEN Mod. N1410 provides 4 independent High Voltage channels in a single width NIM mechanics. Each channel can provide a ±1kV max voltage, a 200 µA max current. The output polarity is independently selectable for each channel. Channels have common floating return (common return insulated from the crate ground); HV outputs are delivered through SHV connectors. The HV output Ramp-up and Ramp-down rates may be selected independently for each channel in the range 1÷100 V/s in 1 V/s steps. The module features 5 nA Iset/Imon resolution. Features include Imon Zoom, increasing resolution to 500 pA.
|
SHV connector
NIM single width, 4 channels for Mod. N1410 |
Consult our connectors reference page for technical information.
Power supply control can be performed either locally, assisted by a Graphic color display or remotely, via USB, RS232 or RS485, the latter allowing to build a daisy chain network of modules N14XX. It is also controllable via TCP/IP by the Smart Fan Unit of CAEN NIM8301.
A complete set of free software Tools is available to control this unit: GECO2020 with user friendly GUI and CAEN HV Wrapper library for custom SW development. EPICS and LabVIEW also supported.
Safety features allows the module to perform as a current generator and includes:
| Overvoltage and Undervoltage warning | when the output voltage differs from the programmed value by more than 2% of set value (minimum 1V). |
| Overcurrent detection | if a channel tries to draw a current larger than its programmed limit, it enters TRIP status, keeping the maximum allowed value for a programmable time (TRIP), before being switched off. |
| Hardware VMAX | Programmable VMAX protection limit. |
| Common Interlock logic | for channels enable/disable and individual inputs signal for channel Kill function. |
Module control can take place either locally, assisted by a Graphic colour display, or remotely, via USB (1) or RS485 (1). It is also controllable via TCP/IP (2) by the Smart Fan Unit of CAEN NIM8301 crate.
Available Options:
- A1480 DC Input Power Equalizer.
N14xx modules are provided with a USB VCP interface and can be programmed via PC by connecting the PC USB port with the N14xx USB B-type port; the featured controller (FT232BM chip) requires a driver available on this page or at www.ftdichip.com
Technical Specifications
- Packaging
Single width NIM unit
- Output channels
4 channels, Common Floating Return, SHV connector Positive or Negative Polarity (requires internal setting)
- Output ranges
1 kV / 200 µA (IMRANGE = High)
1 kV / 20 µA (IMRANGE = Low) – Imon Zoom Active
- Max. Ch. Output Power
200 mW
- Vset Resolution
20 mV
- Vmon Resolution
20 mV
- Iset Resolution
5 nA
- Imon Resolution
5 nA (IMRANGE = High)
500 pA (IMRANGE = Low) – Imon Zoom Active
- Vmax
0 ÷ 1050 V; absolute maximum HV level that the channel is allowed to reach, independently from the preset value Vset. Output voltage cannot exceed the preset value Vmax. The accuracy is 0.2 % ± 20mV
- Vmax resolution
± 0.1 V
- Ramp Up/Down
1÷100 Volt/s, 1 Volt/s step
- Trip
- Max. time an “overcurrent” can last (seconds). A channel in “overcurrent” works as a current generator; output voltage varies in order to keep the output current lower than the programmed value.
- “Overcurrent” lasting more than set value (1 to 9999) causes the channel to “trip”.
- Output voltage will drop to zero either at the Ramp-down rate or at the fastest available rate, depending on Power Down setting; in both cases the channel is put in the OFF state.
- Trip range: 0 ÷ 999.9 s; 1000 s = INFINITE. Step = 0.1 s (If trip= INFINITE, “overcurrent” lasts indefinitely).
- Voltage Ripple
- 10 ÷ 1000 Hz. Typical: 3 mVpp / Maximum: 5 mVpp
- 1 ÷ 20000 kHz. Typical: 3 mVpp / Maximum: 5 mVpp
- Vmon vs. Vout Accuracy
±0.02% of read value ±500 mV
- Vset vs. Vout Accuracy
±0.02% of read value ±500 mV
- Imon vs. Iout Accuracy
±2% of read value ±20 nA (IMRANGE = High)
±2% of read value ±2 nA (IMRANGE = Low) – Imon Zoom Active
- Iset vs. Iout Accuracy
±2% of read value ±30 nA (IMRANGE = High)
±2% of read value ±3 nA (IMRANGE = Low) – Imon Zoom Active
- Humidity range
0 ÷ 80%
- Operating temperature
0 ÷ 45°C
- Storage temperature
-10 ÷ 70°C
- Vout / Temperature coefficient
max. 50 ppm/°C
- Imon / Temperature coefficient
max 100 ppm/C°; max 300 ppm/C° with Imon zoom
- Long term stability Vout vs. Vset
± 0.02% (after one week @ constant temperature)
Compare
Compare with NIM High Voltage Power Supplies.
Loading...
Ordering Options
| Code | Description |
|---|---|
| WN1410XAAAAA | N1410 - 4Ch Reversible 1000 V/200 µA NIM HV Power Supply Module RoHS |
Related Products
NV8020A
7U CRATE VME/NIM 8 slot VME64 365W, 5 slot NIM 150W
NIM8306
2 Slot Switching 750 W Mini Crate
NIM8305
2 Slot Switching 450 W Mini Crate
NIM8304
7U 12 slot smart fan unit Switching 2000 W Crate
NIM8303
5U 12 slot 300/600 W Crate
NIM8302
5U 10 slot 150 W Compact Crate
NIM8301
7U 12 slot smart fan unit 300/600 W Crate
Related Software
SW1470
Control Software for NIM Power Supply Modules
LabVIEW Driver (PSM - Power Supply Modules)
LabVIEW Instrument Driver for Power Supply Modules
GECO2020
GEneral COntrol Software for CAEN HV Power Supplies
EPICS IOC (PSM Power Supply Modules)
EPICS IOC for Power Supply Modules
CAEN HV Wrapper Library
Library for CAEN Power Supply Control