A1626
16 Channel 1kV/10mA Individual Floating Channel Board
Features
- 16 independently controllable full floating channels
- 1kV / 10mA output range
- 50 mV voltage monitor resolution
- Current monitor resolution:
- high range: 1 µA
- low range: 100 nA
- Programmable voltage ramp up / down rates
- Typical voltage ripple smaller than 3 mVpp (1 KHz ÷ 20 MHz)
- Overcurrent programmable protections
- Programmable TRIP parameter
- DB37 connector
- Current generator operation in overcurrent condition
Overview
A1626 is a single width board (5TE wide) that houses 16 individual floating channels, delivered through DB37 connector. The output voltage is 0 ÷ 1000 V with 50mV set/monitor resolution. The maximum current value is 10mA with a 1 µA setting resolution.

DB37 connector
Single width (5 TE wide),16 channels (Mod. A1626)
Consult our connectors reference page for technical information.
The channels share a Individual Floating Channels, which allows on-detector grounding, reducing the noise level. A global enable/disable connector allows to disable the channels. The voltage ramp rates may be set independently for each channel and offer dual current ranges (software selectable).
The output channels offer dual current ranges (software selectable).
High Power | 0 ÷ 10 mA | I set resolution: | 1 µA | I mon resolution: | 1 µA | Max. power: | 10W |
High Resolution: | 0 ÷ 1 µA | I set resolution: | 1 µA | I mon resolution: | 100 nA |
Independently programmable for each channel:
Output voltage: | 0 ÷ 1 kV | step: 50 mV |
Current limit: | 0 ÷ 10 mA | step: 1 µA |
HV Ramp up/down: | 1 ÷ 250 V/sec | step: 1 V/sec |
TRIP parameter: | 0 ÷ 999.9 s; 1000 s = Infinite | step: 0.1 s |
Safety features allows the module to perform as a current generator and includes:
- Channels can be enabled or disabled through the Global Interlock logic.
- Overvoltage and Undervoltage warning when the output voltage differs from the programmed value.
- Overcurrent detection: when a channel attempts to exceed the programmed current limit, it signaled to be in “overcurrent” and enter in a TRIP status. The output voltage is varied to keep the current below the programmed limit for a programmable TRIP time, then the channel is switched off. If TRIP is set to “constant current mode”, the channel behaves like a current generator.
- Hardware VMAX: maximum output voltage can be set, via front panel potentiometer, at the same common value for all the board channels. VMAX value can be read out via software.
Technical Specifications
- No. of Channels
16 Individual Floating (±50V isolation)
- Output Voltage
0 ÷ 1000 V
- Max Current
10 mA
- Voltage Set Resolution
50 mV
- Voltage Monitor Resolution
50 mV
- Current Set Resolution
1 µA
- Current Monitor Resolution
Low range: 100 nA
High range: 1 µA
- VMAX hardware accuracy
tbd
- VMAX software resolution
1V
- Ramp Up/Down
1÷250 Volt/sec, 1 Volt/sec step
- Ripple (@ max load with 10nf)
1 KHz ÷ 20 MHz maximum: <5 mV pp
typical: <3 mV pp
10 Hz ÷ 1 KHz maximum: <10 mV pp
typical: <5 mV pp
- Voltage Monitor vs Output Voltage Accuracy
typical: ±0.05 % ±0.2 V
maximum: ±0.05 % ±0.5 V
- Voltage Set vs Output Voltage Accuracy
typical: ±0.05 % ±0.2 V
maximum: ±0.05 % ±0.5 V
- Current Monitor vs. Output Current Accuracy
high range typical: ±1 % ±3 µA
high range maximum: ±1% ±10 µA
low range typical: ±1% ±300 nA
low range maximum: ±1% ±1 µA
- Current Set vs. Output Current Accuracy
typical: ±1 % ±3 µA (start 5% Vnom.)
maximum: ±1% ±10 µA (start 5% Vnom.)
- Output Connector
DB37 Multipin
Compare
Compare with High Voltage Power Supply.
Loading...
Ordering Options
Code | Description |
---|---|
WA1626MXAAAA | A1626M - SYx527 mixed polaryty individual floating16ch 1kV/10mA (10W) board RoHS |
WA1626NXAAAA | A1626N - SYx527 negative individual floating 16ch 1kV/10mA (10W) board RoHS |
WA1626PXAAAA | A1626P - SYx527 positive individual floating 16ch 1kV/10mA (10W) board RoHS |
WA1626ENBXAA | A1626ENB - Enable Board for A1625 RoHS |